Mark this thread as Sold
Pfab Stage 2 *Complete* E85 Ready!
10-28-2013, 09:13 PM
#1
Registered User
Thread Starter
Pfab Stage 2 *Complete* E85 Ready!
Hey guys,
I have a Pfab Stage 2 Kit up for sale! It's a complete kit and ready to be bolted on and ran and is E85 capable/ready. The kit has approx 4k miles of use and the turbo was recently rebuilt by Turbo Power in Cameron Park. Turbo has about 2k miles and has no shaft play. I'm going to try to list everything included, but please excuse me if I miss something small. The kit includes the following:
PFAB Topmount ELT manifold (Reinforced to prevent cracking)
Precision 6262 Journal Bearing with .82 hotside and .065 Oil Restrictor (No thrust shaft play)
K&N High Flow Filter (Not pictured, whoops)
PFAB Stainless steel downpipe (3" DP)
PFAB Stainless steel midpipe w/ flexpipe + jet hot coating (Test pipe welded onto midpipe)
PFAB Stainless Steel dumptube
TiAL 44mm wastegate (Black)
TiAL Q 50mm blow off valve (Silver)
PFAB Intercooler piping kit
CX Racing Intercooler (Same dimensions as Pfab Stage 2 Intercooler)
ATP Turbo Catch Can with PCV fittings for AP2 Valve Cover (Direct fit + Mounting Hardware)
Injector Dynamics 1000cc Injectors w/ PNP Clips (E85 Ready)
Aeromotive 340lph Fuel Pump (E85 Ready)
Hondata 4 Bar MAP Sensor
Hallman Pro Manual Boost Controller w/ mounting hardware
AEM Boost Gauge w/ sensor and wiring
AEM UEGO Wideband w/ o2 sensor and wiring
AEM EMS V1 w/ serial to USB Cable and Jeff Evans tune for this exact set up on an F22 (Most up to date firmware)
HKS 3" Single w/ v-band to midpipe (Includes diff mounting hardware for exhaust hanger, not pictured, whoops again)
Fast Line Performance AP1 Bumper Cap w/ hardware (To cover the driver side exhaust outlet)
-3 AN Oil Feed
-10 AN Oil Drain
Fitting for oil feed and stock oil pressure sender unit
Brand new nuts and bolts for turbo to turbo manifold
All v-band clamps + gaskets
Again, this kit is complete. It's a direct bolt on kit, but does require the battery to be relocated and the fusebox/EPS to be repositioned. This kit has been amazing to me and felt awesome. I've never dyno'd it, but it has seen 1 track day where I ran a 13.3 at 108 MPH and another run at 13.4 at 110 MPH (It's my DD, so relax lol). This kit has a lot of potential for power and the spool is amazing as a lot of Pfabs products are proven for reliability, customer service and power!
At this time, I am not looking to part out anything. Would rather keep it as a whole for now. I've decided to sell my S2000, so I am returning to stock to hopefully interest potential buyers. Payment methods include local pick up or PayPal or whatever is convenient for you and safe for me. The kit is off of the car and just needs to be packaged and shipped.
Price is set at $5,500 SHIPPED. I accept PayPal and credit/debit cards via PayPal in person or over the phone! All of this stuff, together, retails for over $8,000 EASY. If my price seems unfair, please send me a PM or the comment will be deleted. Once paid for, I will need about 2 days to package and ship it all. I have plenty of local and nationwide vouches, please purchase with confidence. Here are some photos and a brief YouTube video of the parts:
[[VIDEO PENDING]]
If interested, I can be reached at 916-607-4525, my name is Steve. In the event I do not pick up, please shoot me a text or leave me a voicemail and I'll call you back.
I have a Pfab Stage 2 Kit up for sale! It's a complete kit and ready to be bolted on and ran and is E85 capable/ready. The kit has approx 4k miles of use and the turbo was recently rebuilt by Turbo Power in Cameron Park. Turbo has about 2k miles and has no shaft play. I'm going to try to list everything included, but please excuse me if I miss something small. The kit includes the following:
PFAB Topmount ELT manifold (Reinforced to prevent cracking)
Precision 6262 Journal Bearing with .82 hotside and .065 Oil Restrictor (No thrust shaft play)
K&N High Flow Filter (Not pictured, whoops)
PFAB Stainless steel downpipe (3" DP)
PFAB Stainless steel midpipe w/ flexpipe + jet hot coating (Test pipe welded onto midpipe)
PFAB Stainless Steel dumptube
TiAL 44mm wastegate (Black)
TiAL Q 50mm blow off valve (Silver)
PFAB Intercooler piping kit
CX Racing Intercooler (Same dimensions as Pfab Stage 2 Intercooler)
ATP Turbo Catch Can with PCV fittings for AP2 Valve Cover (Direct fit + Mounting Hardware)
Injector Dynamics 1000cc Injectors w/ PNP Clips (E85 Ready)
Aeromotive 340lph Fuel Pump (E85 Ready)
Hondata 4 Bar MAP Sensor
Hallman Pro Manual Boost Controller w/ mounting hardware
AEM Boost Gauge w/ sensor and wiring
AEM UEGO Wideband w/ o2 sensor and wiring
AEM EMS V1 w/ serial to USB Cable and Jeff Evans tune for this exact set up on an F22 (Most up to date firmware)
HKS 3" Single w/ v-band to midpipe (Includes diff mounting hardware for exhaust hanger, not pictured, whoops again)
Fast Line Performance AP1 Bumper Cap w/ hardware (To cover the driver side exhaust outlet)
-3 AN Oil Feed
-10 AN Oil Drain
Fitting for oil feed and stock oil pressure sender unit
Brand new nuts and bolts for turbo to turbo manifold
All v-band clamps + gaskets
Again, this kit is complete. It's a direct bolt on kit, but does require the battery to be relocated and the fusebox/EPS to be repositioned. This kit has been amazing to me and felt awesome. I've never dyno'd it, but it has seen 1 track day where I ran a 13.3 at 108 MPH and another run at 13.4 at 110 MPH (It's my DD, so relax lol). This kit has a lot of potential for power and the spool is amazing as a lot of Pfabs products are proven for reliability, customer service and power!
At this time, I am not looking to part out anything. Would rather keep it as a whole for now. I've decided to sell my S2000, so I am returning to stock to hopefully interest potential buyers. Payment methods include local pick up or PayPal or whatever is convenient for you and safe for me. The kit is off of the car and just needs to be packaged and shipped.
Price is set at $5,500 SHIPPED. I accept PayPal and credit/debit cards via PayPal in person or over the phone! All of this stuff, together, retails for over $8,000 EASY. If my price seems unfair, please send me a PM or the comment will be deleted. Once paid for, I will need about 2 days to package and ship it all. I have plenty of local and nationwide vouches, please purchase with confidence. Here are some photos and a brief YouTube video of the parts:
[[VIDEO PENDING]]
If interested, I can be reached at 916-607-4525, my name is Steve. In the event I do not pick up, please shoot me a text or leave me a voicemail and I'll call you back.
10-28-2013, 09:47 PM
#3
Registered User
Thread Starter
Thank you! All parts have been labeled as well. Each set of bolts will be placed in ziplocks for their appropriate locations.
Also, all hoses have been labeled to where they belong for the wastegate, BOV and manual boost controller as well as the boost gauge. Intercooler piping has been labeled to where they are supposed to be fitted too, hence the blue painters tape. Lol.
Also, all hoses have been labeled to where they belong for the wastegate, BOV and manual boost controller as well as the boost gauge. Intercooler piping has been labeled to where they are supposed to be fitted too, hence the blue painters tape. Lol.
10-29-2013, 06:29 AM
#5
Registered User
Thread Starter
Thank you! I'm a little OCD when it comes to organizing parts that I'm selling. I'm sure I could have made it look prettier, but they're all shaped weird. Lol. Everything hose, clamp, nut/bolt etc has been labeled though. Whoever purchases it next should have a fairly breezy install.
.