NEW EBAY HEADER... ?
#1
Banned
Thread Starter
Join Date: May 2005
Location: San Antonio Texas
Posts: 208
Likes: 0
Received 0 Likes
on
0 Posts
NEW EBAY HEADER... ?
Has anyone seen these...?
Cheap, stainless steel and what not...
Just another worse-than-stock header or does anyone think it can actually give you gains?
Whose in to take the plunge?
http://cgi.ebay.com/ebaymotors/00-01-02-06...1QQcmdZViewItem
I think I might do it...
Cheap, stainless steel and what not...
Just another worse-than-stock header or does anyone think it can actually give you gains?
Whose in to take the plunge?
http://cgi.ebay.com/ebaymotors/00-01-02-06...1QQcmdZViewItem
I think I might do it...
#6
hey.zup. i took the plunge on this one just right after i saw it.and i say its worth it. my gtech pro claims an increase of 4.6hp-6.3hp on 5 runs to measure the 1/4 mile. vtec kicks in smooter and sounds better. personally i like it. and i just got mine for $129 plus s&h of 30.
1/4 mile without the generic s2k heder--13.7 (i have a spoon style snorkle, spoon filter, custom catback (single canister)and test pipe, spoon sw388 16x8R and 16x7F. advan a048 on all corners, spoon engine torque dampner, oni quick clutch, hondata intake gasket, spoon springs, x brace and strut bars. 2 kevlar seibon seats-0nly weighs 3lbs vs the stock seats.
during my 5 runs- my results wer between 13.4 (lowest)-- 13.6 (highest).
also, i was by the 1/8 drag strip at irwindale,ca. and before the fastest time i got there befopre the header with my current set up was 8.8 with 100octane but i hit a 8.7 with the headers and with just 91 octane of gas.
so i say it works....
1/4 mile without the generic s2k heder--13.7 (i have a spoon style snorkle, spoon filter, custom catback (single canister)and test pipe, spoon sw388 16x8R and 16x7F. advan a048 on all corners, spoon engine torque dampner, oni quick clutch, hondata intake gasket, spoon springs, x brace and strut bars. 2 kevlar seibon seats-0nly weighs 3lbs vs the stock seats.
during my 5 runs- my results wer between 13.4 (lowest)-- 13.6 (highest).
also, i was by the 1/8 drag strip at irwindale,ca. and before the fastest time i got there befopre the header with my current set up was 8.8 with 100octane but i hit a 8.7 with the headers and with just 91 octane of gas.
so i say it works....
Trending Topics
#9
Banned
Thread Starter
Join Date: May 2005
Location: San Antonio Texas
Posts: 208
Likes: 0
Received 0 Likes
on
0 Posts
- jirro22
??
Is the header well built and everything??
Have you done some actual dyno's with it on to see the increase?
Wow NOW im getting into this haha (still trying to figure out the ultimate way to make the s2000 fast while staying n/a; how it was meant to be)
??
Is the header well built and everything??
Have you done some actual dyno's with it on to see the increase?
Wow NOW im getting into this haha (still trying to figure out the ultimate way to make the s2000 fast while staying n/a; how it was meant to be)