What did you do to your S2000 today?
#483
Yep - still snowing here in MN. I think in a couple weeks it will warm enough to get mine out of deep storage down the road and into shallow storage in my garage until the roads are fixed enough for me to start dailying it for the summer again.
#484
#485
First Mods
New owner her, have had my 2006 since late Feb. Have done the following so far:
1. Alpine UTE-62BTE headunit in place of OEM. Wired with Modifry (thanks Bob, your help and guidance were invaluable) DCI harness and his right side (flush install behind the audio door) phone bracket. Works perfect!
2. Mounted the Pro Clip Large Core IOAuto Magnetic phone mount (Pro Clip IOAuto Mount) on the Modifry bracket. This is a serious mount that is stable, has swivel movement in all directions and looks absolutely OEM. Again it works perfect! Thanks to member ZeroPsi for the reccomendation. Saw it in his car and knew that was the one for me.
3. Bought a 2 for $12 (shipped!) cupholder pair off of ebay and used one on the right footwell. Mounted with the lower rear storage net mounting location and a 1/2 inch longer screw that I got for less than a buck at Lowe's. The bottom folds flat against the floor crossmember and holds bottled water (all I've tried so far) very securely. Thanks to member rudyy for sharing this with me.
4. Installed, but haven't yet been able to wire a single USB power port on the lower right dashpanel. I can get +12V from the fuse panel spade terminal, but can't find a suitable ground location that I can get to in the drivers footwell. Any suggestions would be super!
5. Installed clear sidemarker lights with Joey's SuperNova LED's. Also did interior lights, trunk, and cargo compartments with his products. Joey is a sponsor (JS2K) and treated me well, especially whjen our new puppy found a pair his light/harness units and chewed them up! Joey was most understanding in assisting me in getting another pair to replace them. I;m sure they are high quality and quite durable, but they are NOT puppy proof!
6. Installed the Honda Euro Accessory 2 piece floor mats from Hendy Honda in the UK. Love the more finished look and the quality is MUCh better than US OEM "cheapo" mats.
I'll attach a few pics, love this car and looking at shift knobs next.
1. Alpine UTE-62BTE headunit in place of OEM. Wired with Modifry (thanks Bob, your help and guidance were invaluable) DCI harness and his right side (flush install behind the audio door) phone bracket. Works perfect!
2. Mounted the Pro Clip Large Core IOAuto Magnetic phone mount (Pro Clip IOAuto Mount) on the Modifry bracket. This is a serious mount that is stable, has swivel movement in all directions and looks absolutely OEM. Again it works perfect! Thanks to member ZeroPsi for the reccomendation. Saw it in his car and knew that was the one for me.
3. Bought a 2 for $12 (shipped!) cupholder pair off of ebay and used one on the right footwell. Mounted with the lower rear storage net mounting location and a 1/2 inch longer screw that I got for less than a buck at Lowe's. The bottom folds flat against the floor crossmember and holds bottled water (all I've tried so far) very securely. Thanks to member rudyy for sharing this with me.
4. Installed, but haven't yet been able to wire a single USB power port on the lower right dashpanel. I can get +12V from the fuse panel spade terminal, but can't find a suitable ground location that I can get to in the drivers footwell. Any suggestions would be super!
5. Installed clear sidemarker lights with Joey's SuperNova LED's. Also did interior lights, trunk, and cargo compartments with his products. Joey is a sponsor (JS2K) and treated me well, especially whjen our new puppy found a pair his light/harness units and chewed them up! Joey was most understanding in assisting me in getting another pair to replace them. I;m sure they are high quality and quite durable, but they are NOT puppy proof!
6. Installed the Honda Euro Accessory 2 piece floor mats from Hendy Honda in the UK. Love the more finished look and the quality is MUCh better than US OEM "cheapo" mats.
I'll attach a few pics, love this car and looking at shift knobs next.
#487
detailed the interior of the new '06 I picked up Friday- it was a Good Friday indeed! then just tightened the Front roll bar end links. Just getting the '03 ready for the next owner.
darcy
darcy
#490
I'm in the process of installing a turbo kit. Just ordered mishimoto fan shrouds because the IC piping won't fit with stock fans. Also ordered an ATP fitting to fit the wastegate to positive pressure on the turbo