2004-05 cylinder head versus 2006+ - Page 2 - S2KI Honda S2000 Forums

Go Back  S2KI Honda S2000 Forums > General Interest > S2000 Under The Hood
Reload this Page >

2004-05 cylinder head versus 2006+

Notices
S2000 Under The Hood S2000 Technical and Mechanical discussions.

2004-05 cylinder head versus 2006+

 
Old 05-11-2018, 03:59 AM
  #11  
Moderator
 
Billman250's Avatar
 
Join Date: Jul 2002
Location: Long Island, New York
Posts: 20,573
Thanked 221 Times in 177 Posts
Default

^Correct.

Nothing needs to be done at all. Just leave the steel snake shaped cover in place.
Billman250 is online now  
Old 05-11-2018, 07:45 AM
  #12  
 
Chuck S's Avatar
 
Join Date: Jul 2014
Location: Chesterfield VA
Posts: 6,804
Thanked 217 Times in 211 Posts
Default

Posting identical questions in multiple locations just fragments the responses.

You milled the block. Not sure what effect this will have and it was noted but not answered in either of these fragmented threads.

-- Chuck
Chuck S is offline  
Old 05-15-2018, 06:59 AM
  #13  
 
Join Date: Jul 2013
Posts: 154
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Originally Posted by flanders View Post
Those holes leads back to to intake side of the head and on a non dbw car it connects to the intake manifold.
Your dbw intake manifold doesn't have this opening and will just block it off.
Thanks for clearing that up. I appreciate it. Are the intake/exhaust manifold gaskets & head gaskets all the same for all the S2000 years? I already bought the gaskets for my 2006. Thanks.
Silver_Bullet_S is offline  
Old 05-15-2018, 07:01 AM
  #14  
 
Join Date: Jul 2013
Posts: 154
Thanks: 0
Thanked 0 Times in 0 Posts
Default

Originally Posted by Billman250 View Post
^Correct.

Nothing needs to be done at all. Just leave the steel snake shaped cover in place.
thanks for the info
Silver_Bullet_S is offline  
Old 05-15-2018, 09:11 AM
  #15  
Moderator
 
Billman250's Avatar
 
Join Date: Jul 2002
Location: Long Island, New York
Posts: 20,573
Thanked 221 Times in 177 Posts
Default

Originally Posted by Silver_Bullet_S View Post
Are the intake/exhaust manifold gaskets & head gasket all the same for all the S2000 years?
All the same.
Billman250 is online now  
Old 01-12-2019, 07:46 AM
  #16  
 
Join Date: Aug 2010
Posts: 232
Thanks: 0
Thanked 5 Times in 5 Posts
Default

Slightly different question from my side, have searched it, but just to make sure.

I have an early 2002 S2000. lower block is shot and I can get a new (F20c) 2009 lower block.

Is it plug and play, on my 2002 head, intake and harness / sensors? I believe it is, since there are almost no difference in the lower blocks through the years.

Thank you very much.

Last edited by Delta_lima; 01-12-2019 at 07:48 AM.
Delta_lima is offline  
Old 01-12-2019, 01:50 PM
  #17  
 
Slowcrash_101's Avatar
 
Join Date: Jul 2013
Posts: 3,637
Thanked 62 Times in 61 Posts
Default

Originally Posted by Delta_lima View Post
Slightly different question from my side, have searched it, but just to make sure.

I have an early 2002 S2000. lower block is shot and I can get a new (F20c) 2009 lower block.

Is it plug and play, on my 2002 head, intake and harness / sensors? I believe it is, since there are almost no difference in the lower blocks through the years.

Thank you very much.
crank sensor needs to be swapped otherwise no difference other than displacement. If you're in europe disregard that last bit.
Slowcrash_101 is online now  
Old 01-12-2019, 02:01 PM
  #18  
 
Join Date: Aug 2010
Posts: 232
Thanks: 0
Thanked 5 Times in 5 Posts
Default

Its both a F20c (2,0)

not sure if the new engine will come with a crank sensor. But the old one (2002) will be mounted,
thank you!

is the harness plug different? Or a different sensor?
Delta_lima is offline  
Old 01-12-2019, 02:32 PM
  #19  
 
flanders's Avatar
 
Join Date: Aug 2013
Location: Sweden
Posts: 2,570
Thanked 120 Times in 117 Posts
Default

Both plug and sensor is different, you will also need to replace the trigger wheel.
flanders is online now  
Old 01-12-2019, 03:06 PM
  #20  
 
Join Date: Aug 2010
Posts: 232
Thanks: 0
Thanked 5 Times in 5 Posts
Default

Ai, serious? That would mean to remove a factory sealed carter and chain cover :/
Delta_lima is offline  

Quick Reply: 2004-05 cylinder head versus 2006+


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands