S2KI Honda S2000 Forums - Search Results

Search: Posts Made By: Charper732
Showing results 1 to 13 of 13
Search took 0.03 seconds.
05-28-2019, 11:57 AM
Replies: 39
Views: 2,114
Posted By Sarén-Swe

Went with Samsonas, 6speed sequential. Got...

Went with Samsonas, 6speed sequential.

Got around 3,5k rpm with full boost. Can still rev some more..but time will tell:) So Will probably raise the rev limit if needed.
04-29-2019, 09:35 AM
Replies: 14
Views: 3,448
Posted By lyao1

IA - J's Racing complete f22c spec 3A and Urge Design itb

FS: J's Racing longblock complete f22c spec 3A and Urge Design itb

First Name: Shane
Price: $8500 for engine
$2200 for itb
Location: Ames, Iowa
Contact: email [email protected] or text...
04-18-2019, 06:07 AM
Replies: 21
Views: 1,239
Posted By scottdh20

ill break down what he was saying a bit. psi is a...

ill break down what he was saying a bit. psi is a irrelevant number. literally the only time that number matters is estimating how much psi you will need to run to achieve a hp goal and select an...
09-04-2018, 10:57 PM
Replies: 1
Views: 344
Posted By xproteK

Thumbs up Charper732 Seller Feedback

Wanted to give some extremely positive feedback to Charper732 for a perfect transaction.

I purchased an AP2 a few weeks ago that had a bad motor. I made a thread looking for a new motor within a...
06-05-2018, 11:03 AM
Replies: 37
Views: 3,728
Posted By flexer

Walbro just announced the release of the new 525...

Walbro just announced the release of the new 525 pump. This new pump now flows the exact same as the newly released DW400 at the pressures turbo cars typically run.
03-25-2018, 05:26 PM
Replies: 76
Views: 12,860
Posted By fatjoe10

I'm approaching this from an experimental...

I'm approaching this from an experimental perspective. I got a mule vehicle set up for this. I want to experiment so that someone may look and say "look he tried 87.50mm and it was a total failure."...
12-21-2017, 07:50 AM
Replies: 9
Views: 1,052
Posted By arsenal

1. I raised one side up, 2. Removed the lower...

1. I raised one side up,
2. Removed the lower link and loosened the top link on side raised
3. Then lowered back down.
4. Went to the other side and loosened the end link
5. Recentered the bolt...
04-06-2017, 03:39 AM
Replies: 5
Views: 424
Posted By liquid_helix136

What if I told you there was a proven way for you...

What if I told you there was a proven way for you to grow your penis in just two weeks to the size you've always longed for? Which also has the benefit of saving that failing marriage? Its just one...
01-24-2017, 06:39 PM
Replies: 5
Views: 2,070
Posted By 1nate7

Who is they? You need 70.1mm for the front,...

Who is they? You need 70.1mm for the front, widely available from multiple sources.
...
01-02-2017, 03:57 PM
Replies: 16
Views: 1,355
Posted By S2KPUDDYDAD

if you feather the gas a little bit when you...

if you feather the gas a little bit when you disengage the clutch it helps, there is a learning curve to it. Be careful harsh engagement/disengagement puts shock on the driveline and can cause...
01-02-2017, 03:37 PM
Replies: 16
Views: 1,355
Posted By S2KPUDDYDAD

The ACT full kit will not engage and disengage...

The ACT full kit will not engage and disengage like stock, it is a lot more grabby. B serious asked all the right questions about the install.
01-02-2017, 03:11 PM
Replies: 16
Views: 1,355
Posted By B serious

with the assumption that everything is properly...

with the assumption that everything is properly installed, and you don't have broken engine/trans/diff mounts, or problems with axles.....

did you buy a new flywheel or resurface your existing...
01-01-2012, 05:22 AM
Replies: 39
Views: 5,881
Posted By Billman250

Guys...the camwheel bolt coming loose was the...

Guys...the camwheel bolt coming loose was the cause. The OP even stated he found it loose. The camwheel is pressure fed. Once that bolt comes lose, all head pressure is lost through the port in the...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands