DIY brake Bleeding
Thread Starter
Registered User
Joined: Nov 2006
Posts: 91
Likes: 0
DIY brake Bleeding
What is the bleeding order for an 05 S? I saw a post listing Driver F, Passenger F, PR, DR for an 00-01, is it still the same for an 05?
I'm used to doing the one furthest from the Master cylinder, then working your way towards it.
I'm used to doing the one furthest from the Master cylinder, then working your way towards it.
Joined: Apr 2005
Posts: 970
Likes: 2
Instead of starting a new thread, I'll just piggy-back on this one.
I want to replace my brake fluid with ATE, but I don't know what needs to be done. I was told that I'll need to flush the entire system, which will require about 2 gallons of fluid. Can I do this flush myself? Because I also read to never empty the reservoir.
Another general question: When you bleed your brakes you are replacing a portion of the fluid, right? What purpose does that serve if the majority of your fluid goes unchanged? Won't the old mix with the new?
I want to replace my brake fluid with ATE, but I don't know what needs to be done. I was told that I'll need to flush the entire system, which will require about 2 gallons of fluid. Can I do this flush myself? Because I also read to never empty the reservoir.
Another general question: When you bleed your brakes you are replacing a portion of the fluid, right? What purpose does that serve if the majority of your fluid goes unchanged? Won't the old mix with the new?
Joined: Jan 2006
Posts: 4,953
Likes: 25
From: 17 ft below sea level.
s2krazy01 Posted on Apr 22 2007, 06:12 PM
The procedure is described very well in the stickies on top of UTH.
Straingly enough.. it's this post
(yeah.. I went back to the future... or simular)
2 gallons!!
Thats 7 liters!
You would have enough..
IMO a complete flush can be done with 1/2 - 1 liter just to be safe.
Depending on your wrenching skills.
If the level gets too low you're introducing air into the system = bad.
IMO only a small bit of fluid inside the ABS pump will not be refreshed but will mix with the old as soon as ABS comes into play.
I want to replace my brake fluid with ATE, but I don't know what needs to be done.
Straingly enough.. it's this post
(yeah.. I went back to the future... or simular)
I was told that I'll need to flush the entire system, which will require about 2 gallons of fluid.
Thats 7 liters!
You would have enough..
IMO a complete flush can be done with 1/2 - 1 liter just to be safe.
Can I do this flush myself?
Because I also read to never empty the reservoir.
When you bleed your brakes you are replacing a portion of the fluid, right? What purpose does that serve if the majority of your fluid goes unchanged? Won't the old mix with the new?
Moderator
Joined: Jul 2002
Posts: 22,378
Likes: 1,822
From: Long Island, New York
EDIT:
I have revised this procedure that is detailed in the rest of this thread.
Please go here for the new procedure:
https://www.s2ki.com/s2000/topic/995...eding-revised/
I have revised this procedure that is detailed in the rest of this thread.
Please go here for the new procedure:
https://www.s2ki.com/s2000/topic/995...eding-revised/
Trending Topics
Joined: Jan 2006
Posts: 4,953
Likes: 25
From: 17 ft below sea level.
Billman250 Posted on Apr 23 2007, 02:22 AM
Gravity is your friend
Maybe this post should be in the stickies?
Oh.. well.. maybe when the new forum is online.
Start with the right front bleeder. Attach a clear hose, and let it gravity bleed till it turns blue.
Repeat for the remaining wheels.
Repeat for the remaining wheels.
Maybe this post should be in the stickies?
Oh.. well.. maybe when the new forum is online.
