The quest for "Flushness" using AP2 OEM Wheels!
12-22-2014, 05:16 PM
#1233
first time using my spacers. had to put my ap2v2s back on while my 18" HREs got completely redone (they're done but not mounted yet).
215/45/17 & 245/40/17 Dunlop Direzza DZ-101 (from previous owner)
15mm hubcentric spacer in front
20mm hubcentric spacer in rear
not sure how much lower i am now. was way more slammed than this, but had car raised when i got my new Buddy Club N+ coilovers and cornerbalanced alignment (worth every penny!)
front & rear fenders rolled completely flat w/rear tabs relocated. NO rubbing w/these ap2v2s, but slight rubbing in rear w/HRES on big bumps
doesn't look bad, but can't wait until i get my HREs back on. looks like i can easily go w/a 20mm front & 25mm rear spacer. that was the setup another member rec'd to me. he had a significant amount of experience w/the OEM ap2 wheels & spacers. however, he said i should stick to 15mm & 20mm on stock studs. i didn't want to get extended studs.
03-17-2015, 06:35 AM
#1236
Registered User
Join Date: Nov 2013
Location: Langley, BC
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
04-07-2015, 04:18 AM
#1239
Back for round 2 with my 2nd S! 
15/20MM...after driving around last night a bit and today...I didn't even have to roll fenders. I'd rather take the fender approach very slowly if need be, this time around.
With a push from my buddy Dennis...gave DMV motorsport spacers a shot...great quality...fixed center, 17MM nuts on the 15 and 19MM on the 20...
Had to sand and apply some bearing grease (I always do for ease of removal later). Also, a little trick I use to put the spacers on the front by myself using a breaker bar.
DSC_8098 by swimex37, on Flickr
DSC_8101 by swimex37, on Flickr
DSC_8102 by swimex37, on Flickr
Before:
DSC_8099 by swimex37, on Flickr
After:
DSC_8103 by swimex37, on Flickr
Absolutely perfect...not too aggressive, but pretty flush!
DSC_8116 by swimex37, on Flickr
DSC_8117 by swimex37, on Flickr
DSC_8120 by swimex37, on Flickr
DSC_8126 by swimex37, on Flickr
DSC_8128 by swimex37, on Flickr
I'm slightly less low than I was on the Sebring one...I can still get the jack under the sides without 2x4.
DSC_8129 by swimex37, on Flickr
15/20MM...after driving around last night a bit and today...I didn't even have to roll fenders. I'd rather take the fender approach very slowly if need be, this time around.
With a push from my buddy Dennis...gave DMV motorsport spacers a shot...great quality...fixed center, 17MM nuts on the 15 and 19MM on the 20...
Had to sand and apply some bearing grease (I always do for ease of removal later). Also, a little trick I use to put the spacers on the front by myself using a breaker bar.
DSC_8098 by swimex37, on FlickrDSC_8101 by swimex37, on FlickrDSC_8102 by swimex37, on FlickrBefore:
DSC_8099 by swimex37, on FlickrAfter:
DSC_8103 by swimex37, on FlickrAbsolutely perfect...not too aggressive, but pretty flush!
DSC_8116 by swimex37, on FlickrDSC_8117 by swimex37, on FlickrDSC_8120 by swimex37, on FlickrDSC_8126 by swimex37, on FlickrDSC_8128 by swimex37, on FlickrI'm slightly less low than I was on the Sebring one...I can still get the jack under the sides without 2x4.
DSC_8129 by swimex37, on Flickr
04-08-2015, 10:32 AM
#1240
Back for round 2 with my 2nd S!
15/20MM...after driving around last night a bit and today...I didn't even have to roll fenders. I'd rather take the fender approach very slowly if need be, this time around.
With a push from my buddy Dennis...gave DMV motorsport spacers a shot...great quality...fixed center, 17MM nuts on the 15 and 19MM on the 20...
Had to sand and apply some bearing grease (I always do for ease of removal later). Also, a little trick I use to put the spacers on the front by myself using a breaker bar.
DSC_8098 by swimex37, on Flickr
15/20MM...after driving around last night a bit and today...I didn't even have to roll fenders. I'd rather take the fender approach very slowly if need be, this time around.
With a push from my buddy Dennis...gave DMV motorsport spacers a shot...great quality...fixed center, 17MM nuts on the 15 and 19MM on the 20...
Had to sand and apply some bearing grease (I always do for ease of removal later). Also, a little trick I use to put the spacers on the front by myself using a breaker bar.
DSC_8098 by swimex37, on FlickrEdit - I'm assuming these are them? http://www.ebay.com/itm/HUBCENTRIC-B...-/181465918184
I'm always a little weary of eBay-born products. They seem decent enough from your review and pictures though. I may just give them a shot.