Momo steering wheel and 2 ohm resistor not working
03-18-2010, 11:36 AM
#11
Moderator
Originally Posted by skool u,Mar 18 2010, 10:13 AM
I guess I'll try taking out the one under the dash and ensure that the top resistor is wired well and i'll reset the ecu again and see if that works.
The resistor should be plugged in b4 the cable reel. I guess if there is a yellow connector going into the cable reel under the dash that would work to but i cant tell without seeing it.
Stop resetting the ECU and do this
https://www.s2ki.com/forums/index.php?showt...dpost&p=2109198
03-18-2010, 12:04 PM
#12
Banned
Join Date: Nov 2005
Posts: 2,929
Likes: 0
Received 0 Likes
on
0 Posts
Most hubs dont work with the SRS reel. It needs to be removed. You can wire your cruise control buttons easily (See pic below, cruise set and resume are the 2 black push buttons).
Here's mine. Steering wheel position is the same as stock, not to close, not to far. Take mesurements and play with the spacers and you'll be fine.
As for the SRS reset, its a procedure that you need to know by heart for it to go right since there are some steps you have to follow them fast so no time to read from a paper. I used a normally open push button for the SRS reset jumper on the fuse box to connect/disconnect as needed while on the reset procedure. Makes it way easier.
Here's mine. Steering wheel position is the same as stock, not to close, not to far. Take mesurements and play with the spacers and you'll be fine.
As for the SRS reset, its a procedure that you need to know by heart for it to go right since there are some steps you have to follow them fast so no time to read from a paper. I used a normally open push button for the SRS reset jumper on the fuse box to connect/disconnect as needed while on the reset procedure. Makes it way easier.
03-18-2010, 12:26 PM
#13
Registered User
Thread Starter
Join Date: Sep 2008
Location: Calgary, Alberta
Posts: 487
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Gigdy,Mar 18 2010, 11:36 AM
yes 3.3 works fine, but all you need is 2.2.
The resistor should be plugged in b4 the cable reel. I guess if there is a yellow connector going into the cable reel under the dash that would work to but i cant tell without seeing it.
Stop resetting the ECU and do this
https://www.s2ki.com/forums/index.php?showt...dpost&p=2109198
The resistor should be plugged in b4 the cable reel. I guess if there is a yellow connector going into the cable reel under the dash that would work to but i cant tell without seeing it.
Stop resetting the ECU and do this
https://www.s2ki.com/forums/index.php?showt...dpost&p=2109198
06-16-2010, 04:24 AM
#15
Originally Posted by skool u,Mar 19 2010, 02:01 PM
Does anyone have any photos or descriptions on how to properly install that 2.2 ohm resistor?
Which leads do you connect the 2ohm resistor? Here's the SRS connector from my 06.
06-18-2010, 09:35 AM
#18
Ok.. I wasn't able to defeat the SRS warning w/ the resistors that came w/ the Works Bell hub. So I bought 2.2ohm resistors from Radio Shack, cleared the SRS memory, & now no SRS light.
Here's how I placed the 2.2ohm resistor on the SRS connector.
Here's what came w/ the Works Bell hub.
I hope this helps!
Here's how I placed the 2.2ohm resistor on the SRS connector.
Here's what came w/ the Works Bell hub.
I hope this helps!
02-21-2011, 09:55 PM
#19
Registered User
Join Date: Nov 2004
Location: Bay Area, CA
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
Where do you guys put the resistors on 2004 and 2005 S2K. I believe the resistors on 04-05 are different then 06+. Do I need to put in two resistors on the cable reel and bottom of the dash panel?