Custom A/C relocation lines for your boosted car or tucked bay!
06-13-2011, 07:32 PM
#143
Registered User
Join Date: Apr 2011
Posts: 665
Likes: 0
Received 0 Likes
on
0 Posts
Installed my kit today. This is a high quality kit. I am very satisfied w/ the purchase. It's great to have a/c again especially summer is around the corner. I also picked up some thermal wrap and wrapped up the a/c lines, hoses and wires near the manifold. I had some questions during the install and david responded right away. 
for customer service. Here are some pics of the install! Thanks again david!
I had a fat leak in the A/C system would not hold pressure. Put dye in the system and found my leak. The low pressure side line was rubbing against my upper IC piping and made a big hole.
Before
After
Stock A/C line going into trash.
for customer service. Here are some pics of the install! Thanks again david!I had a fat leak in the A/C system would not hold pressure. Put dye in the system and found my leak. The low pressure side line was rubbing against my upper IC piping and made a big hole.
Before
After
Stock A/C line going into trash.
06-13-2011, 11:40 PM
#144
Registered User
Thread Starter
looks good! You freaked me out when you said I sent you the wrong fittings, glad we got it all sorted out via telephone. I have to update the install guide as its for the old style kits I used to make and is kinda of confusing with the new kits that go straight to the compressor.
Thanks again!
Thanks again!
06-20-2011, 07:27 AM
#145
Registered User
Thread Starter
Only 2 kits left and then I am out of stock for a few weeks waiting on parts to come from my suppliers to make the kits.. So if you need this asap you better jump on it.
06-20-2011, 12:14 PM
#146
Registered User
Join Date: Feb 2009
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
Located in Portland Oregon
Plenty of vouches on kits I have sold.
Includes the 2 hoses, all oem o rings, reduced barrier hose for maximun flexibility and all the fittings needed. Also the 1oz of pag oil to be placed back into the line so the proper level is achieved.
225 shipped to the lower 48 states for the new standard length kits
Pm me for paypal info
Combo The A/c kit with an Alloy Craft heater bracket for a total of 255 shipped. A complete relocation package.
The kit runs behind the motor and around to keep all the ac lines on the drivers side of the engine bay.
Photos courtesy of "Torque Obsessed"Fittings installed:
New lines connected:
I used a jigsaw to cut away the plastic pieces so they'd fit. Didn't do the best work, but hey it's done...
Then I made a crappy bracket to bend the other hoses away from the exhaust manifold so I could remove the heat shield.
2008 fully tucked cr with my through the fender kit. **Only available by special order and has a lead time.**
Here are a few pics of my engine bay kit "camuman" (anthonys) car. He has an sot kit, what a mess it makes of the engine bay.
His install thread: https://www.s2ki.com/forums/index.ph...pic=724920&hl=
Before on camumans car
After on the same car
06-20-2011, 12:29 PM
#147
Registered User
Join Date: Feb 2009
Posts: 178
Likes: 0
Received 0 Likes
on
0 Posts
hi i want to purchase the kit for my 07 s2000 the complete relocation package. email me @ hieus2k@att.net for the paypal info .. and do you have the extent kit not the one run through fender . thankyou
Located in Portland Oregon
Plenty of vouches on kits I have sold.
Includes the 2 hoses, all oem o rings, reduced barrier hose for maximun flexibility and all the fittings needed. Also the 1oz of pag oil to be placed back into the line so the proper level is achieved.
225 shipped to the lower 48 states for the new standard length kits
Pm me for paypal info
Combo The A/c kit with an Alloy Craft heater bracket for a total of 255 shipped. A complete relocation package.
The kit runs behind the motor and around to keep all the ac lines on the drivers side of the engine bay.
Photos courtesy of "Torque Obsessed"Fittings installed:
New lines connected:
I used a jigsaw to cut away the plastic pieces so they'd fit. Didn't do the best work, but hey it's done...
Then I made a crappy bracket to bend the other hoses away from the exhaust manifold so I could remove the heat shield.
2008 fully tucked cr with my through the fender kit. **Only available by special order and has a lead time.**
Here are a few pics of my engine bay kit "camuman" (anthonys) car. He has an sot kit, what a mess it makes of the engine bay.
His install thread: https://www.s2ki.com/forums/index.ph...pic=724920&hl=
Before on camumans car
After on the same car
[/quote]
Located in Portland Oregon
Plenty of vouches on kits I have sold.
Includes the 2 hoses, all oem o rings, reduced barrier hose for maximun flexibility and all the fittings needed. Also the 1oz of pag oil to be placed back into the line so the proper level is achieved.
225 shipped to the lower 48 states for the new standard length kits
Pm me for paypal info
Combo The A/c kit with an Alloy Craft heater bracket for a total of 255 shipped. A complete relocation package.
The kit runs behind the motor and around to keep all the ac lines on the drivers side of the engine bay.
Photos courtesy of "Torque Obsessed"Fittings installed:
New lines connected:
I used a jigsaw to cut away the plastic pieces so they'd fit. Didn't do the best work, but hey it's done...
Then I made a crappy bracket to bend the other hoses away from the exhaust manifold so I could remove the heat shield.
2008 fully tucked cr with my through the fender kit. **Only available by special order and has a lead time.**
Here are a few pics of my engine bay kit "camuman" (anthonys) car. He has an sot kit, what a mess it makes of the engine bay.
His install thread: https://www.s2ki.com/forums/index.ph...pic=724920&hl=
Before on camumans car
After on the same car
[/quote]
