S2000 Talk Discussions related to the S2000, its ownership and enthusiasm for it.

Go to your engine and check your...

Thread Tools
 
Old Mar 26, 2003 | 02:57 PM
  #11  
GEARHEAD's Avatar
20 Year Member
 
Joined: Mar 2002
Posts: 588
Likes: 7
From: Bellingham
Default

Having extra slack in your throttle cable should not cause any idle or performance problems. Most Honda throttle bodies have an idle adjustment screw that will fine tune your idle. You should never use the tension in your throttle cable to change your idle speed. As the engine moves around in the engine bay your idle/throttle will change if you have no slack in your cable.
Old Mar 26, 2003 | 03:04 PM
  #12  
efthimios's Avatar
Registered User
 
Joined: Oct 2002
Posts: 14,430
Likes: 1
From: OH
Default

i was having the same problem taking off in first.....i'm going outside right now!
Old Mar 26, 2003 | 04:15 PM
  #13  
ninegrand's Avatar
Registered User
 
Joined: Oct 2002
Posts: 2,492
Likes: 0
From: Lake Tittycaca
Default

For what it's worth, I adjusted mine to about 1/2" slack (from 1") tonight and went for a short drive with a noticed change. Not huge but enough to notice with easier throttle control and a bit better response.

Thanks for the heads up Rdriver!
Old Apr 7, 2003 | 04:28 PM
  #14  
Destiny2002's Avatar
Registered User
 
Joined: Feb 2002
Posts: 2,960
Likes: 2
From: Transporter
Default

OMG, I can't believe how out-of-spec my cable was, like 3 times the play required!

My car only has 7600 miles, it couldn't have loosened that much since new...

Tools: Small scale/ruler and 12mm open-end wrench.

Engine off.

Check free play by lifting the middle of the exposed cable up with your finger with very light force. Check with a ruler, If it deflects more than 1/4 inch, it needs adjusted.

Loosen 12mm locknut, the one toward the front of the car by pushing the wrench away from you. Keep turning locknut a few more turns to get it out of the way. Turn adjusting nut (the one on the other side of the bracket) with 12mm wrench until the slack in the cable is where it is supposed to be (1/4 inch deflection when lifting up). Turn locknut back down and tighten. Double-check slack.

If you have any driving problems or excess idle, check adjustment again, you may have moved the adjusting nut too far towards tight.
Old Apr 7, 2003 | 04:37 PM
  #15  
Da Hapa's Avatar
Registered User
 
Joined: Mar 2001
Posts: 4,101
Likes: 0
From: Dana Point, CA
Default

please read this
Old Apr 7, 2003 | 07:04 PM
  #16  
north9586's Avatar
Registered User
 
Joined: Dec 2001
Posts: 1,911
Likes: 0
From: Ladera Ranch, CA
Default

Da Hapa...................I almost feel as though I could kiss you.
Old Apr 7, 2003 | 09:13 PM
  #17  
Da Hapa's Avatar
Registered User
 
Joined: Mar 2001
Posts: 4,101
Likes: 0
From: Dana Point, CA
Default

Originally posted by north9586
Da Hapa...................I almost feel as though I could kiss you.
Easy there, big fella. My wife will get jealous.
Old Apr 12, 2003 | 02:42 PM
  #18  
wicky's Avatar
20 Year Member
Photogenic
 
Joined: Jul 2002
Posts: 42,828
Likes: 74
From: stuffed in a box
Default

Holy Cow, I just did this myself.... I had the same experience destiny2000 did..... 3/4" worth of play either way. My throttle cable actually SAGGED when it was at idle.......... If you haven't done this, do it. Clutching and rev-matching is like a hot knife thru butter now..... Worth every single one of the 2 minutes it took
Old Apr 12, 2003 | 02:44 PM
  #19  
wicky's Avatar
20 Year Member
Photogenic
 
Joined: Jul 2002
Posts: 42,828
Likes: 74
From: stuffed in a box
Default

PS - I now have a bit of the "excess high idle" but I am able to blip the throttle and it go down to stock idle..... wonder if my butterfly or something is sticky... probably the pulley on the throttle..... since I can blip it closed I'm going to leave it for now.....
Old Apr 12, 2003 | 02:48 PM
  #20  
StrangeDaze's Avatar
Registered User
 
Joined: Aug 2001
Posts: 2,805
Likes: 0
From: Columbus, OH
Default

[QUOTE]Originally posted by wicky
[B]Holy Cow, I just did this myself.... I had the same experience destiny2000 did..... 3/4" worth of play either way.



All times are GMT -8. The time now is 09:42 PM.