Texas - Central Texas S2000 Owners Central Texas S2000 Owners

Rag Top

Thread Tools
 
Old Dec 13, 2010 | 05:20 PM
  #1  
meaziz's Avatar
Thread Starter
Registered User
 
Joined: Nov 2010
Posts: 91
Likes: 0
From: San Antonio
Default Rag Top

Anyone know how to disassemble the rag top. I need to drill out the rear rivets for the driver side strap. Can't get back there with a drill. Anyone out there with the knowledge and a rivet gun!
Thanks
Dan
Reply
Old Dec 13, 2010 | 08:07 PM
  #2  
Mr3plus1's Avatar
Registered User
 
Joined: May 2008
Posts: 286
Likes: 0
From: San Antonio
Default

Where are you located?
Reply
Old Dec 13, 2010 | 08:23 PM
  #3  
meaziz's Avatar
Thread Starter
Registered User
 
Joined: Nov 2010
Posts: 91
Likes: 0
From: San Antonio
Default

Near 1604 and Braun Rd
Reply
Old Dec 13, 2010 | 09:01 PM
  #4  
My01Steve2k's Avatar
Registered User
 
Joined: May 2010
Posts: 12
Likes: 0
From: Tampa, FL
Default

Why do you need to drill it out? IF you're planning to replace the straps I hope you have seen this :
http://www.modifry.com/products/ctf/index.htm
Reply
Old Dec 14, 2010 | 06:53 AM
  #5  
meaziz's Avatar
Thread Starter
Registered User
 
Joined: Nov 2010
Posts: 91
Likes: 0
From: San Antonio
Default

That's the problem. The passenger side had the OEM strap which I cut and used the Modifry strap. Works perfectly. The driver side had the rivets drilled out so I bought rivets from Home Depot and Honda put them in. The problem!
those rivets don't leave the hole the OEM rivets leave to put the pins in using Modifry. So, I need to drill those out and replace them with the OEM rivets I have now. ( I hope they leave the hole required for the Modifry)
Hope that makes sense.. I didn't know anything about the roof when I bought the car. Just something else Josh, (StoK) didn't tell me about. A royal pain in the a_s.
Reply
Old Dec 14, 2010 | 08:49 AM
  #6  
Mr3plus1's Avatar
Registered User
 
Joined: May 2008
Posts: 286
Likes: 0
From: San Antonio
Default

The OEM rivets wont fit. The holes sretch out and the replacement ones end up wiggling around in there. You have to bump up to the next size up.

Its not hard to peel the top back that far. Open it about 1/2 way. Undo all the screws holding in the panel along the front top part. Peel the rubber off the front two pieces by the windows and take all those screws out. There is a rivet at the front corner on both sides of the top holding in a metal tab. Drill it out. Use a screwdriver to pry the metal tab that holds the inside of the top in along that front bar. That should allow you to peel the top back far enough to drill out the strap rivets and replace the strap.

I honestly dont like the modifry strap. If you dont have a rivet gun and dont feel comfortable peeling the top back about half way I totally understand, but if you've got the tools you might as well do it the right way. Whole process would take about an hour honestly.
Reply
Old Dec 14, 2010 | 05:11 PM
  #7  
meaziz's Avatar
Thread Starter
Registered User
 
Joined: Nov 2010
Posts: 91
Likes: 0
From: San Antonio
Default

I want to do it the right way. I don't feel real confident with what you instructed. I'm afraid I will be doing damage and then it will be cost me more in the long wrong. If you have the time, case of beer?
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
alphalanos
S2000 Modifications and Parts
15
Mar 22, 2014 06:28 AM
bluerennfahrer
S2000 Modifications and Parts
4
Sep 24, 2013 11:00 AM
WhiteS2k
California - Bay Area S2000 Owners
5
May 1, 2012 08:03 AM
zherbo
S2000 Under The Hood
4
Feb 22, 2010 08:20 AM




All times are GMT -8. The time now is 07:20 AM.